Blog posts tagged with 'curved steel staircases'

One of Southern California's iconic, flagship waterfront restaurant sites - 1360 North Harbor Drive along the North Embarcadero, is getting a facelift! The Port of San Diego and The Brigantine, Inc. began construction in July 2018 to redevelop Portside Pier including introducing four new dining concepts and enhancing the panoramic views of San Diego Bay for daily visitors. Albina Co., Inc. provided 60,000 pounds of various bent materials for the unique curved roof structure as well as for two signature spiral staircases that leads from the dock to the second floor public walkway and viewing deck.

Materials bent by Albina Co., Inc. included:
TS 14" X 6" X .500" WALL A500 GR B (6 pieces spiral bent the easy way as tight as a 17 ft plan view radius, 4 pieces bent the easy way as tight as a 17 ft inside radius).
TS 12" X 6" X .500" WALL A500 GR B (8 pieces bent the easy way as tight as a 2’ 7” outside radius, 8 pieces spiral bent the easy way as tight as a 2’ 7” plan view radius).
TS 8" X 8" X .500" WALL A500 GR B (84 pieces bent to various radii and configurations).
TS 18" X 6" X .375" WALL A500 GR B (4 pieces bent the hard way).
W10 X 12# A992 (9 pieces bent the hard way).
W18 X 35# A992 (15 pieces bent the hard way).
W16 X 26# A992 (2 pieces bent the hard way).
W14 X 22# A992 (13 pieces bent the hard way).

The event is—"Curved Rails: From Field to Fabrication" August 9th & 10th in Erie, Colorado.

Living Design Studios will be the host shop. This shop is the home to Jonathan Falk who will be the 2020-2021 NOMMA President.

Terry Barrett, Pinpoint Solutions, and Matt Olseng, MDO Welding and Fabrication, will be the presenters. They will teach the basics of field measuring; transforming the measurements in to shop drawings and getting the project “off the paper” and into physical form. Matt will demonstrate fabrication of curved rails and share tips for success.

Albina was thrilled to be able to donate some curved steel parts to be used in the seminar. Visit the NOMMA Homepage to register!

The Albina Co., Inc. team recently spiraled a true HSS stair stringer to a very tight configuration for a spiral staircase project in Washington. The project consisted of using an induction heat source, on our custom made bending equipment, to spiral bend tube steel 16" X 12" X .625" WALL A500 GR B the easy way to a 77” Center Line Radius. VERY TIGHT and VERY IMPRESSIVE! Great work team!

Back in June, I posted a picture of some induction heating process, for the new American Airlines headquarters in Fort Worth, Texas. In addition to the 16" square, we produced another set of 

The 1.7 million-square-foot complex, dubbed the “Trinity complex,” consists of constructing four seven-story buildings. It will cost at least $300 million to build and will house over 6,500 employees. There are 10 tower cranes on the project and there will be more than 1,000 construction workers on-site during the peak. It is scheduled to open during the second half of 2019.  These are the type of bends that ONLY Albina can do!

We recently spiral bent tube steel 12" X 8" X .625" WALL A500 GR B Spiral the Easy way to a 173” radius for a customer spiral staircase located in Utah. Square and rectangular tubing is also known as HSS (hollow structural steel). Albina has the ability to bend both square and rectangular tubing. For rectangular tubing we can bend both the easy way (against the weak axis) and the hard way (against the strong axis). We can even provide Multi-Plane bending where we are bending both the easy way AND the hard way. Albina is a unique shop in that we can bend very small square materials such as TS ½” x ½” x .049” wall all of the way up to very large materials such as TS 20” x 12” x .625” wall, which happens to be the largest size that mills produce. Albina actually has a larger capacity than TS 20” x 12” x .625” wall, which means we can bend materials larger then what the mills produce!

Albina recently used our induction heating process to spiral bend Tube Steel 16" X 16" X .625" WALL A500 GR B bent down to a an 18 foot radius for the new American Airlines headquarters in Fort Worth, Texas. The 1.7 million-square-foot complex, dubbed the “Trinity complex,” consists of constructing four seven-story buildings. It will cost at least $300 million to build and will house over 6,500 employees. There are 10 tower cranes on the project and there will be more than 1,000 construction workers on-site during the peak. It is scheduled to open during the second half of 2019. Including the 16" square, we have produced another set of spirals and have one in the queue. The one in the queue is Tube Steel 14" x 6" x .625" wall REALLY tight, exposed and bent to a 5'-6" radius on a 45° pitch. We already made a mock up for the job and all parties loved it. These are the type of bends that ONLY Albina can do! This is a really amazing project! Stay tuned for more pictures.

Albina recently spiral bent several stringers for a state of the art spiral staircase for the Buddy Holly Hall of Performing Arts and Sciences in Lubbock, Texas. The Lubbock Entertainment and Performing Arts Association (LEPAA) has had the vision for this building since 2013 and broke ground just over a year ago in April 2017. The dance center will contain the entire operation of Ballet Lubbock, including six dance studios, parent and community space, production areas and administrative offices and expected to be complete in early 2020. Check out this website for artist renderings of the building and interior features such as the spiral staircase we bent consisting of: TS 16" X 8" X .625" WALL A500 GR C 16 pcs: Spiral bend the easy way Bent down to a 7 ft plan view radius. TS 10" X 6" X .625" WALL A500 GR C 10 pcs: Spiral bend the hard way Bend down to a 14’ 11” plan view radius.