Tag Archives: spiral stringers

Spiral Stringers Help Create Stunning Staircase at Altar’d State at The Forum Shops at Caesar’s Palace

Albina Co., Inc. recently rolled 16 pieces of 5/8″ plate A36 to as tight as a 162″ radius. Six pieces of plate were used as the inside stringers of a beautiful spiral staircase at Altar’d State at the Forum Shops at Caesar’s Palace. Six pieces of plate were used as the outside stringers of the staircase, and four pieces were used on the landings. We bent the stringers, trimmed rectangular treat cut outs, trimmed to length, match paired plates, tacked them together and match drilled all holes. We bolt matched the plates together with a 6 bolts, (2) on the end, (2) in the middle, and (2) on the other end.

We also bent 2½” X 2½” X ¼” ANGLE A36 to help create the spiral staircase. Materials included:

1 piece leg in to a 25” inside radius.  Albina to bend 180° minimum.

1 piece leg out to a 162” inside radius.  Albina to bend 70” minimum arc.

1 piece leg out to a 30” inside radius.  Albina to bend 36” minimum arc.

1 piece leg out to a 19” inside radius.  Albina to bend 80” minimum arc.

1 piece leg in to a 38” inside radius.  Albina to bend 180° minimum.

Lastly, we bent one piece of Flat Bar 5/8″ x 12″ A36 UM Plate leg in to a 38” inside radius and 180° minimum.

Tweet
Share
Share

Spiral Staircases at the Newly Renovated Space Needle

Albina Co. Inc. bent the spiral staircases at the newly renovated Space Needle in Seattle, Washington. The Space Needle’s rotating glass floor, dubbed “The Loupe”, is located just below the open-air observation deck and Albina Co., Inc. was the steel bender/roller for the custom spiral staircases connecting the two areas. Albina Co., Inc. bent 1″ thick x 13 ¼” wide A572 GR 50 to yield three 180″ pieces and three 144″ pieces of rolled plate and 1″ thick x 10-13/16″ wide A572 GR 50 to yield one 80″ piece of rolled plate. We also bent tube steel 10″ x 6″ x .625″ WALL A500 GR B to a 11’ 6” inside plan view radius (the easy way). 

Space Needle Spiral Staircase at "The Loupe"
Backside view of spiral staircase at the Space Needle
People walking on the spiral staircase at the Space needle
the space needle
Tweet
Share
Share

VERY TIGHT Spiral Stringer!

The Albina Co., Inc. team recently spiraled a true HSS stair stringer to a very tight configuration for a spiral staircase project in Washington. The project consisted of using an induction heat source, on our custom made bending equipment, to spiral bend tube steel 16″ X 12″ X .625″ WALL A500 GR B the easy way to a 77” Center Line Radius. VERY TIGHT and VERY IMPRESSIVE! Great work team! 

Extremely tight spiral stringer for custom spiral staircase
Tweet
Share
Share

Install Progress Picture of Curved Steel Spiral Staircase for the New American Airlines Headquarters in Fort Worth, Texas

Back in June, I posted a picture of some spiral bent Tube Steel 16″ X 16″ X .625″ WALL A500 GR B bent down to a an 18 foot radius, using our induction heating process, for the new American Airlines headquarters in Fort Worth, Texas. In addition to the 16″ square, we produced another set of spirals consisting of Tube Steel 14″ x 6″ x .625″ wall REALLY tight, exposed and bent to a 5′-6″ radius on a 45° pitch. Below is a progress picture of the installation of these spiral stringers.

steel spiral stringers for custom spiral staircase at new American Airlines Headquarters in Fort Worth, Texas

The 1.7 million-square-foot complex, dubbed the “Trinity complex,” consists of constructing four seven-story buildings. It will cost at least $300 million to build and will house over 6,500 employees. There are 10 tower cranes on the project and there will be more than 1,000 construction workers on-site during the peak. It is scheduled to open during the second half of 2019.  These are the type of bends that ONLY Albina can do!

Tweet
Share
Share

Spiral Rolled Plate for Spiral Staircase in Multi-Million Dollar Luxury Home on Green Street in San Francisco, CA.

We recently spiral rolled 1/2″ and 1″ plate for a custom spiral staircase in a multi-million dollar luxury home on Green Street in San Francisco, California.
We provided the rolled plate for the staircase and then flat plane rolled the plate for the landings. The tightest radius was a 29.75” center line radius.

Spiral Rolled Plate for spiral staircase on Green Street in San Francisco, CA.

Spiral Rolled Plate for spiral staircase on Green Street in San Francisco, CA.

Spiral Rolled Plate for spiral staircase on Green Street in San Francisco, CA.

Tweet
Share
Share

Curved Steel Spiral Staircase for the New American Airlines Headquarters in Fort Worth, Texas

Albina recently used our induction heating process to spiral bend Tube Steel 16″ X 16″ X .625″ WALL A500 GR B bent down to a an 18 foot radius for the new American Airlines headquarters in Fort Worth, Texas. The 1.7 million-square-foot complex, dubbed the “Trinity complex,” consists of constructing four seven-story buildings. It will cost at least $300 million to build and will house over 6,500 employees. There are 10 tower cranes on the project and there will be more than 1,000 construction workers on-site during the peak. It is scheduled to open during the second half of 2019. Including the 16″ square, we have produced another set of spirals and have one in the queue. The one in the queue is Tube Steel 14″ x 6″ x .625″ wall REALLY tight, exposed and bent to a 5′-6″ radius on a 45° pitch. We already made a mock up for the job and all parties loved it. These are the type of bends that ONLY Albina can do! This is a really amazing project! Stay tuned for more pictures.

Curved Steel spiral stringer American Airlines Headquarters

Curved Steel spiral stringer American Airlines Headquarters

Curved Steel spiral stringer American Airlines Headquarters

Curved Steel spiral stringer American Airlines Headquarters

Tweet
Share
Share

Curved Steel Spiral Stair Stringers at Suffolk County Community College

Suffolk County Community College (SCCC), recently opened its new $30 million, 75,000 square foot Learning Resource Center (LRC) and library on the Michael J. Grant Campus in Brentwood, Long Island, New York. Albina Co., Inc. bent the steel spiral stringers for the project. The steel spiral stringers consisted of spiral bent tube steel 20″ X 4″ X .500″ WALL A500 GR B the easy way to a 14 ft. plan view radius. We also bent the landings to a similar radius. We also spiral bent tube steel 14″ X 10″ X .500″ WALL A500 GR B the easy way to a 19 ft. plan view radius and the landings also to a similar radius.

Curved Steel Spiral Stair Stringers Suffolk County Community College-1

Curved Steel Spiral Stair Stringers Suffolk County Community College-1

Tweet
Share
Share

Curved Steel Spiral Staircase at the Capitol Visitors Center in Washington, D.C.

On a recent trip to Washington DC, we had the pleasure of touring the Capitol Building and we were able to capture some pictures of The Capital Visitors Center spiral staircase we bent years ago. The project consisted of flat and spiral bending of angle, channel, flat bar, solid square, wide flange (up to W18 x 76#) and square tubing (up to 10″ x 10″ x .500″ wall spiral bent).

Capitol Visitors Center Spiral Staircase

Main Landing View of Capitol Visitors Center Spiral Staircase

Capitol Visitors Center Spiral Staircase

Capitol Visitors Center Spiral Staircase

Tweet
Share
Share

Installation of Spiral Staircase at Orange Coast Memorial Hospital

Orange Coast Memorial Medical Center is the only nonprofit hospital in Fountain Valley, CA. Albina recently spiral bent and flat bent Tube Steel 16″ X 8″ X .500″ WALL A500 GR B to 13’ 6” and 18’ 10” plan view radii the easy way to form the spiral stringers for the staircase. See the installation pictures below. Finished install pictures coming soon!

Spiral Staircase Being Lowered by Crane

Spiral Staircase Being Lowered by Crane

Close Up of Install of Spiral Stringers

Close Up of Install of Spiral Stringers

Orange County Memorial Hospital Spiral Stairacase

Orange County Memorial Hospital Spiral Stairacase

Tweet
Share
Share

Extremely Tight Tube Steel Spiral Stringers for Lakeside Campus Building Staircase

Enjoy the latest install pictures of the 20” x 8” x .625” wall tube steel which provides the base supports for a heavy weight bearing spiral staircase at the Lakeside Campus in Richardson, Texas. The tube steel was spiral bent the easy way using our induction heat source and increment bend method. The tube steel was bent down to a 7’ 7” center line (plan view) radius and all bends were to AESS standards. Albina also bent tube steel 20” x 12” x .625” wall for a different section of the spiral staircase. The 20″ x 12″ material was bent down to a 13’ 9” center line (plan view) radius and all bends were to AESS standards.The specifications to bend to a center line radius this tight is almost unheard of, but Albina was able to do it to perfection!

Steel Spiral Stringers for Heavy Weight Bearing Spiral Staircase

Steel Spiral Stringers for Heavy Weight Bearing Spiral Staircase

Tube Steel 20" x 12" and 20" x 8" for Spiral Staircase at Lakeside Campus in Richardson, Texas

Tube Steel 20″ x 12″ and 20″ x 8″ for Spiral Staircase at Lakeside Campus in Richardson, Texas

Steel Spiral Stringers Installed

Steel Spiral Stringers Installed

Tweet
Share
Share