Category Archives: Square and Rectangular Tube Bending

Curved Steel Roof at the M-Car Wash in Davie, Florida

Albina recently completed a great project for a curved steel roof at the M-Car Wash in Davie, Florida

Materials bent for this project included Tube Steel 10″ X 4″ X .250″ WALL A500 GR B yielding 3 pieces. Albina cut the material to length, prepped and primered each piece. Tube Steel 10″ X 4″ X .375″ WALL A500 GR B- yielding 12 pieces bent the hard way.  Albina’s scope of work was to bend, trim, holes, weld caps and grind per drawings.  NOMMA #1 finish welds.  Prep and prime paint after fabrication.  Exposed. We also bent 3″ SCH40 A500 GR B to yeild 15 assemblies.  Albina Cut, Fit, weld and grind per drawings.  NOMMA #1 finish.  Prep and Prime after fabrication.

Curved Steel Roof M-Wash Davie, Florida
Curved Steel Roof M-Wash Davie, Florida

Curved Steel Roof Structure & Spiral Staircases Highlights of the Portside Peir Renovation in San Diego Bay

One of Southern California’s iconic, flagship waterfront restaurant sites – 1360 North Harbor Drive along the North Embarcadero, is getting a facelift! The Port of San Diego and The Brigantine, Inc. began construction in July 2018 to redevelop Portside Pier including introducing four new dining concepts and enhancing the panoramic views of San Diego Bay for daily visitors. Albina Co., Inc. provided 60,000 pounds of various bent materials for the unique curved roof structure as well as for two signature spiral staircases that leads from the dock to the second floor public walkway and viewing deck.

Portside Pier Curved Roof Structure
Portside Pier Curved WIde Flange/Beam Roof Structure
Portside Pier Curved Wide Flange/Beam Structure Enclosed

Materials bent by Albina Co., Inc. included:
TS 14″ X 6″ X .500″ WALL A500 GR B (6 pieces spiral bent the easy way as tight as a 17 ft plan view radius, 4 pieces bent the easy way as tight as a 17 ft inside radius).
TS 12″ X 6″ X .500″ WALL A500 GR B (8 pieces bent the easy way as tight as a 2’ 7” outside radius, 8 pieces spiral bent the easy way as tight as a 2’ 7” plan view radius).
TS 8″ X 8″ X .500″ WALL A500 GR B (84 pieces bent to various radii and configurations).
TS 18″ X 6″ X .375″ WALL A500 GR B (4 pieces bent the hard way).
W10 X 12# A992 (9 pieces bent the hard way).
W18 X 35# A992 (15 pieces bent the hard way).
W16 X 26# A992 (2 pieces bent the hard way).
W14 X 22# A992 (13 pieces bent the hard way).

Portside Pier Steel Spiral Staircase
Portside Pier Steel Spiral Staircase

Curved Steel Canopy at the Calvary Chapel in Ontario, Oregon

Albina recently bent various materials including tube steel, flat bar, pipe and angle for the Calvary Chapel in Ontario, Oregon. The Calvary Chapel is right on the Idaho border. Our bent material helped to create a lovely curved steel canopy for the chapel.

Materials Bent Include:

TS 10″ X 3″ X .375″ WALL A500 GR B (7 lengths x 48 ft- bent the hard way to a 66 ft radius).

FB ½” X 4″ A36 (2 lengths x 20 ft- bent the hard way to a 66 ft radius).

8″ SCH40 A500 GR B (1 length x 42 ft).

TS 6″ X 2″ X .188″ WALL A500 GR B (5 lengths x 48 ft).

1″ X 1″ X ¼” ANGLE A36 (6 lengths x 20 ft).

Curved Steel Canopy at the Calvary Chapel Ontario, Oregon

Curved Steel Helps to Create a Unique & Meaningful Monument in Des Moines

“A Monumental Journey” by Kelly James Marshall for the Greater Des Moines Public Art Foundation. The monument is featured in the August issue of Modern Steel “What’s Cool In Steel.” The monument celebrates the legacy of African American laywers who founded the the National Bar Association in 1925 and the monument symbolizes communication among diverse people and legal system, that while not perfect, strives to be balanced. Find more details about the project in the above article featured in Modern Steel.
Albina bent various materials for this project including:
3 x 40 ft: 5″ X 5″ X 5/16″ ANGLE A36. Cut and bent to net 8 pcs (leg out). Bent down to a 68” inside radius.
1 x 20 ft: MC3 X 7.1# A36. Cut and bent to net 2 pcs (flanges in).
2 x 48 ft: TS 6″ X 6″ X .625″ WALL A500 GR B. Cut and bent to net 4 pcs. Bent down to a 58” inside radius.
1 x 48 ft: TS 6″ X 6″ X .375″ WALL A500 GR B. Cut and bent to net 2 pcs. Bent down to a 77” inside radius.

Kerry James Marshall (American, born 1955) A MONUMENTAL JOURNEY 2018 Manganese Ironspot brick, steel, granite approx. H. 30 ft, D. 19 ft

Commissioned by Greater Des Moines Public Art Foundation; Greater Des Moines Public Art Foundation Collection, 2018.1 Photos: Ben Easter

Curved Steel Monument
Curved Steel Monument
Curved Steel Monument
Curved Steel Monument

“The Spheres” Grace the Cover of Structure Magazine

“The Spheres”, the recipient of the AISC 2019 IDEAS2 Presidential Award for Excellence in Fabrication grace the cover of the August Issue of Structure Magazine! The article focuses on the inspiration, the vision and the design of “The Spheres.” Albina bent 750,000# and 1,050 pieces rectangular tube steel bent the easy way and a portion bent off-axis for this project. Almost 8 miles of welding work and grinding was avoided because of Albina’s ability to bend a portion of the project. Almost NO correction was needed during fabrication or erection as the bends fit to the fixtures within 1/32nd of an inch! Numerous Pacific Northwest businesses collaborated to make The Spheres possible.

Curved Steel Sections of The Spheres Erected
Curved Steel Sections of The Spheres Erected
The Spheres in Seattle Washington
“The Spheres” Seattle, WA.

Difficult, Tight Bends Create Unique Curved Steel Vestibule Frames

Albina recently bent some Tube Steel 6″ X 3″ X .500″ WALL A500 GR B as double 90° bends to a 17″ inside radius the hard way. These are difficult, tight bends for this material and the bends turned out perfectly! The bends will be used as vestibule frames for a lobby entry.

Tube Steel 6" X 3" X .500" WALL A500 GR B as double 90° bends to a 17" inside radius the hard way for vestibule frames
Tube Steel 6" X 3" X .500" WALL A500 GR B as double 90° bends to a 17" inside radius the hard way for vestibule frames
Tube Steel 6" X 3" X .500" WALL A500 GR B as double 90° bends to a 17" inside radius the hard way for vestibule frames

Exterior Images of Curved Steel at The Madison Center “Great Room” in Seattle, Washington

We were in Seattle this weekend and were able to get some exterior pictures of The Madison Center. The Madison Center is a 530 foot tall, 36 story high rise office building in Seattle, Washington and is featured in the June edition of Modern Steel. Albina Co., Inc. was the bender/roller on this project and worked specifically on what is being called “The Great Room” which is a 45-foot tall steel framed entryway rotunda. Albina bent many material types for this project including tube steel 8″ x 6″ up to 12″ x 12″, 3″ x 3″ angle, W10 and W16 wide flange, 8″ pipe and more. Check out the article for some more details on the architectural feat and some great pictures. We will be heading back up to Seattle next week to get some interior shots. Stay tuned!

Exterior Picture of The Madison Center Great Room
The Great Room Rotunda
Close up of Curved Steel Wide Flange, Tube Steel and Pipe
Curved Steel Spiral Staircase

“The Seattle Spheres” win Presidential Award for Excellence in Fabrication

The May 2019 Edition of Modern Steel Magazine features an article on the Seattle Spheres as they won the Presidential Award for Excellence in Fabrication! 


Albina Co., Inc. was the steel bender/roller for the Curved Steel Bio-Sphere buildings in Seattle, WA. Albina bent 750,000# and 1,050 pieces rectangular tube steel bent the easy way and a portion bent off-axis. Almost 8 miles of welding work and grinding was avoided because of Albina’s ability to bend a portion of the project. Almost NO correction was needed during fabrication or erection as the bends fit to the fixtures within 1/32nd of an inch!

Curved Steel Spheres
Curved Steel Spheres Seattle, WA.
Curved Steel Spheres Seattle, WA.

Curved Tube Steel Used on Timber Equipment

We recently completed a project consisting of 400 pieces of bent tube steel 4″ X 4″ X .375″ WALL A500 GR B for a customer on the east coast. All parts were cut and trimmed by Albina to a 1/16” tolerance. These bent parts will be used on equipment for the timber industry. 

Curved Tube Steel Used on Timber Equipment

Curved Steel Tubing for Farming Equipment

We recently completed a great project where our bends will be used for various parts on high-end farming equipment. The bending project consisted of three different material types including:

Tube Steel 5″ X 5″ X .250″ WALL A500 GR B- Albina cut and bent material to net 108 pcs.

curved steel for high-end farming equipment-1

Tube Steel 5″ X 2″ X .250″ WALL A500 GR B- Albina cut and bent material to net 100 pcs.

curved steel for high-end farming equipment-2

Tube Steel 2″ X 2″ X .250″ WALL A500 GR B- Albina cut and bent material to net 403 pcs.

curved steel for high-end farming equipment-3