Albina Co. Inc. bent the spiral staircases at the newly renovated Space Needle in Seattle, Washington. The Space Needle’s rotating glass floor, dubbed “The Loupe”, is located just below the open-air observation deck and Albina Co., Inc. was the steel bender/roller for the custom spiral staircases connecting the two areas. Albina Co., Inc. bent 1″ thick x 13 ¼” wide A572 GR 50 to yield three 180″ pieces and three 144″ pieces of rolled plate and 1″ thick x 10-13/16″ wide A572 GR 50 to yield one 80″ piece of rolled plate. We also bent tube steel 10″ x 6″ x .625″ WALL A500 GR B to a 11’ 6” inside plan view radius (the easy way).
One of Southern California’s iconic, flagship waterfront restaurant sites – 1360 North Harbor Drive along the North Embarcadero, is getting a facelift! The Port of San Diego and The Brigantine, Inc. began construction in July 2018 to redevelop Portside Pier including introducing four new dining concepts and enhancing the panoramic views of San Diego Bay for daily visitors. Albina Co., Inc. provided 60,000 pounds of various bent materials for the unique curved roof structure as well as for two signature spiral staircases that leads from the dock to the second floor public walkway and viewing deck.
Materials bent by Albina Co., Inc. included:
TS 14″ X 6″ X .500″ WALL A500 GR B (6 pieces spiral bent the easy way as tight as a 17 ft plan view radius, 4 pieces bent the easy way as tight as a 17 ft inside radius).
TS 12″ X 6″ X .500″ WALL A500 GR B (8 pieces bent the easy way as tight as a 2’ 7” outside radius, 8 pieces spiral bent the easy way as tight as a 2’ 7” plan view radius).
TS 8″ X 8″ X .500″ WALL A500 GR B (84 pieces bent to various radii and configurations).
TS 18″ X 6″ X .375″ WALL A500 GR B (4 pieces bent the hard way).
W10 X 12# A992 (9 pieces bent the hard way).
W18 X 35# A992 (15 pieces bent the hard way).
W16 X 26# A992 (2 pieces bent the hard way).
W14 X 22# A992 (13 pieces bent the hard way).
The event is—”Curved Rails: From Field to Fabrication” August 9th & 10th in Erie, Colorado.
Living Design Studios will be the host shop. This shop is the home to Jonathan Falk who will be the 2020-2021 NOMMA President.
Terry Barrett, Pinpoint Solutions, and Matt Olseng, MDO Welding and Fabrication, will be the presenters. They will teach the basics of field measuring; transforming the measurements in to shop drawings and getting the project “off the paper” and into physical form. Matt will demonstrate fabrication of curved rails and share tips for success.
Albina was thrilled to be able to donate some curved steel parts to be used in the seminar. Visit the NOMMA Homepage to register!
The Vancouver Waterfront Project and Grant Pier Fabricator A2 Fabrication Earns 2019 Earnest Wiemann Gold Top Job Contest Award!
Albina bent 2½” SCH40 T304 S/S, 1¼” SCH40 T304 S/S, 2½” SCH40 A53B ERW and 1¼” SCH80 A53B ERW for the curved steel handrails. We cut and bent the steel per the drawings and protected the finish of material during production and for shipping by wrapping the curved steel in foam and cardboard to keep parts from rubbing against each other. We bend handrails for commercial, recreational, transportation and residential applications. Handrail Kits Are Available: Bent and trimmed per drawing, mid-rails trimmed and coped, assemblies supplied as individual parts or fabricated complete. Call us for your next handrail project!
We recently completed a project that consisted of rolling 6″ SCH40 A53B ERW to a 18″ center line radius. The project consisted of 54 pieces in total and in going to a company that specializes in bridge and pedestrian railings.
Albina specializes in bending railings and handrails for commercial, recreational, transportation and residential applications. We can bend to customer specifications and we also have handrail kits available. We can bend and trim per drawing, trim and cope mid-rails, and assemblies can be supplied as individual parts or fabricated complete.
The Albina Co., Inc. team recently spiraled a true HSS stair stringer to a very tight configuration for a spiral staircase project in Washington. The project consisted of using an induction heat source, on our custom made bending equipment, to spiral bend tube steel 16″ X 12″ X .625″ WALL A500 GR B the easy way to a 77” Center Line Radius. VERY TIGHT and VERY IMPRESSIVE! Great work team!
Back in June, I posted a picture of some spiral bent Tube Steel 16″ X 16″ X .625″ WALL A500 GR B bent down to a an 18 foot radius, using our induction heating process, for the new American Airlines headquarters in Fort Worth, Texas. In addition to the 16″ square, we produced another set of spirals consisting of Tube Steel 14″ x 6″ x .625″ wall REALLY tight, exposed and bent to a 5′-6″ radius on a 45° pitch. Below is a progress picture of the installation of these spiral stringers.
The 1.7 million-square-foot complex, dubbed the “Trinity complex,” consists of constructing four seven-story buildings. It will cost at least $300 million to build and will house over 6,500 employees. There are 10 tower cranes on the project and there will be more than 1,000 construction workers on-site during the peak. It is scheduled to open during the second half of 2019. These are the type of bends that ONLY Albina can do!
We spent Thanksgiving touring around the beautiful state of Arizona. We saw many of the beautiful sights in Sedona and even went to visit the Grand Canyon. One of the highlights of the trip was our stop at Sloan Park, home of the Chicago Cubs Spring Training. We were anxious to see the field, but equally as excited about getting some pictures of the 50,000 pounds of steel we bent for some custom gates that sit above the stands at the park. The gates hold the overhead field lights. We bent various materials for this project including:
W6 X 15# A992. 80 pcs total. Bent the hard way to a 8’-9” radius.
C6 X 8.2# A36. 42 pcs total bent flanges in to a 10 ft radius.
WT8 X 18# A992. 4 pcs stem out and 6 pcs stem in bent to a 10 ft radius and to a 56 ft radius.
TS 3″ X 3″ X .188″ WALL A500 GR B. 30 pcs bent to a 4’-4” radius and 17 pcs bent to a 11’-6” radius.
4″ X 3″ X ¼” ANGLE A36. 20 pcs total. Some rolled leg in and others leg out. All pcs were bent to a 95 ft – 105 ft radius.
7″ X 4″ X 3/8″ ANGLE A36. 7 pcs rolled leg in and 1 pc rolled let out. All pcs were bent to a 10 ft – 90 ft radius.
MC6 X 18# A36. 4 pcs rolled the hard way to an 11 ft radius.
TS 6″ X 6″ X .250″ WALL A500 GR B. 3 pcs rolled to an 11 ft radius.
8″ X 8″ X ½” ANGLE A36. 3 pcs rolled let out to a 52 ft radius.
Albina worked on a custom spiral staircase for the Ritz Carlton in Sunny Isles, Florida. This high profile spiral staircase was for a great customer out of Florida. When a top of the line luxury hotel needed top of the line bending, Albina was contracted. Yes! We shipped from Oregon to Florida to service the needs of our customer!
Albina bent TS 16″ X 4″ X .500″ WALL A500 GR B down to a 12’ inside radius (for the stringers and the landings). All bends were to AESS standards. Click here for images of the spiral staircase and the newly renovated hotel.
Albina recently completed some very complex spiral bends for a Spiral Staircase which will be installed at the new Moab Hoodoo Hotel, Curio Collection by Hilton in Moab, Utah. The 117-guestroom hotel will offer an upscale lodging option to travelers heading to the Moab desert community. The hotel will be surrounded by large sandstone monoliths that feature balanced stones, known as hoodoos.
Materials bent for the spiral staircase consisted of:
4″ X 4″ X ¼” ANGLE A36
2 pcs bent leg out to a 7′ 4″ inside radius
2 pcs bent leg in to a 13′ 0″ outside radius
C15 X 33.9# A36
2 pcs spiral bent to a 7′ 4″ outside plan radius.
2 pcs spiral bent to a 13′ 0″ inside plan radius.
1 pc bent in a single plane to a 7′ 4″ outside radius
1 pc bent in a single plane to a 13′ 0″ inside radius