We spent Thanksgiving touring around the beautiful state of Arizona. We saw many of the beautiful sights in Sedona and even went to visit the Grand Canyon. One of the highlights of the trip was our stop at Sloan Park, home of the Chicago Cubs Spring Training. We were anxious to see the field, but equally as excited about getting some pictures of the 50,000 pounds of steel we bent for some custom gates that sit above the stands at the park. The gates hold the overhead field lights. We bent various materials for this project including:
W6 X 15# A992. 80 pcs total. Bent the hard way to a 8’-9” radius.
C6 X 8.2# A36. 42 pcs total bent flanges in to a 10 ft radius.
WT8 X 18# A992. 4 pcs stem out and 6 pcs stem in bent to a 10 ft radius and to a 56 ft radius.
TS 3″ X 3″ X .188″ WALL A500 GR B. 30 pcs bent to a 4’-4” radius and 17 pcs bent to a 11’-6” radius.
4″ X 3″ X ¼” ANGLE A36. 20 pcs total. Some rolled leg in and others leg out. All pcs were bent to a 95 ft – 105 ft radius.
7″ X 4″ X 3/8″ ANGLE A36. 7 pcs rolled leg in and 1 pc rolled let out. All pcs were bent to a 10 ft – 90 ft radius.
MC6 X 18# A36. 4 pcs rolled the hard way to an 11 ft radius.
TS 6″ X 6″ X .250″ WALL A500 GR B. 3 pcs rolled to an 11 ft radius.
8″ X 8″ X ½” ANGLE A36. 3 pcs rolled let out to a 52 ft radius.
If you answered yes, than you should consider wearbacks for your elbows. For decades, Albina has supplied customers with bent elbows where we weld a plate or channel to the outside of the bend (acting as the wearback). A wearback is installed to act as an additional layer to the bend, when the backside of an elbow finally is worn through, any materials running in the piping system will remain inside and the piping system will continue to function due to the extra layer of material on the backside of the elbow. We recently bent some 8″ SCH80 T304L S/S SMLS to 30° elbows. After bending the elbows, we bent and fabricated wearbacks out of ½” stainless plate and welded the wearbacks to the outside of the pipe elbows.
Albina Co., Inc. recently rolled 10,000 pounds of channel C15 X 33.9# A36 for The Great Park in Irvine, California. All of the material rolled with the flanges in and is architecturally exposed structural steel. The Great Park is a non-aviation reuse of the decommissioned Marine Corps Air Station (MCAS) El Toro with a focus on sports, agriculture, and the arts. In 2017, two new construction projects were approved and consist of an ice facility and a sports complex. Albina has the ability to bend all mill supplied sizes of channel which includes C3x4.1# through C15x50#.
Rolled Steel Channel at The Great Park
10,000# of C15 X 33.9# A36. All material rolled with the flanges in and is AESS.
Albina Co., Inc. recently completed 14,000 lbs. of bent steel to create a beautiful spiral staircase at Worthy Brewing in Bend, OR. Bent steel materials for the project included:
MC18 X 42.7# A36 spiral bent lengths with flanges in and lengths with flanges out were bent down to a 9 ft plan view radius! Landing pieces were also spiral bent down to a 9’ 8” radius.
C15 X 33.9# A36 for the inside landings were spiral bent down to a 8’ 9” outside radius (plan view).
Bend, Oregon is located on the eastern edge of the Cascade Mountain Range along the Deschutes River and is a popular tourist town known best for the many outdoor activities offered and world famous micro-brews. Worthy Brewing Co. broke ground on Feb. 24, 2012 off U.S. Highway 20 on Bend’s east side — it’s Bend’s 1st east side brewery – and with a beer garden, hop garden, and Hopservatory. The spiral staircase winds up to The Dome at the top of the rotating Hopservatory where visitors can view the cosmic skies through an OGS 16” RC Reflector telescope.
Close up of Spiraled Steel Channel
Spiral Bent Steel Channel
Spiral Staircase Leading to The Hopservatory Dome